Configure-free MPEG4 IP camera with 3GPP/ISMA support

 
   
  General Features:  
 
  • IEEE802.11 b/g wireless interface to provide best installation freedom.
  • Extremely easy installation and usage. Work without a PC connected. Connect up to 20 remote users simultaneously.
  • View the video locally and remotely through the accompanied CamView software immediately after installation.
  • Superior video and audio quality.
 
  System Features:  
 
  • Easily access the camera from anywhere in the world via the ID/password (Through accompanied video management software, no complicated DNS settings needed )
  • 3GPP/ISMA support
  • 802.11 b/g wireless with WEP and WPA security support
  • Connect up to 20 users simultaneously
  • Supports enhanced MPEG-4 compression
  • Supports resolution of up to 640x480 pixels at 30 fps.
  • Free video management software CamView accompanied for easy access and multi-camera management.
  • View video from your Wireless or wired Ethernet network
  • ActiveX video display in Microsoft IE browser.
  • Synchronize the system time through NTP protocol.
  • Built-in Web server for managing via standard web browser.
  • Built-in microphone for synchronized audio.
  • Online Firmware upgrade, will enter safe mode when power is off during critical firmware upgrade point.
  • Watchdog function to prevent system failure.
 
     
Specifications:
 
 Models  StarVedia GC202w
 Power  DC 5V, 1A
 Processors  RISC CPU, hardware video processing and compression.
 Network interface  Ethernet 10BaseT/100BaseTX, Auto-MDIX, RJ-45
 Wireless interface  IEEE 802.11g 6 - 54 Mbps
 IEEE 802.11b 1 - 11 Mbps
 Transmit power: 14.5dBm typically @ 802.11g
 17.5dBm typically @ 802.11b
 Receiver sensitivity: 54Mbps: Typical -73dBm @ 10% PER
 11Mbps: Typical -86dBm @ 10% PER
 Antenna gain: 1.8 dBi
 Image sensor  RGB VGA 1/4 inch CMOS
 Automatic exposure control, automatic white balance, automatic gain control,  automatic brightness control.
 Light sensitivity  0.2 Lux
 Lens  3.2 mm, F2.0, viewing angle: 60.3¢X, fixed iris.
 focus range: 30 cm to infinity
 Buttons  One reset button, to factory default settings
 Indicators  One LED for internet connection status indication
 One LED for Ethernet connection indication
 Enable/disable ¡V web configurable
 Video compression  MPEG-4 Part 2 (ISO/IEC 14496-2) with motion detection, profiles: Simple Profile,  level 0-3
 Frame rate  Up to 30 fps in all resolutions
 Video streaming  MPEG-4
 Separate frame rate/resolution/bandwidth settings for PC and mobile.
 Image settings  Resolution: VGA(640x480), QVGA(320x240), QQVGA(160x120)
 Bandwidth : 64k, 128k, 256k, 512k, 768k, 1M, 1.2M, 1.5M bps
 Frame rate : 5, 10, 15, 20, 25, 30 fps
 Audio  Built-in microphone for audio monitoring
 Audio compression:MP2 audio, AMR-NB for 3GPP/ISMA(RTSP streaming)
 Security  Web management username/password protection
 Video display ID/password protection
 WiFi WEP and WPA security mode
 Installation, management and  maintenance  Installation tool on CD and Web-based configuration
 Automatic configuration backup and restore
 Video management software-CamView for video access and multi-camera  management
 Firmware upgrades via FTP
 Minimum Web browsing and  management software  requirements  Built-in web server for standard web browser access Pentium 4(or  equivalent AMD) CPU 1.0 GHz or higher,1 GB RAM
 Supported protocols  IPv4, HTTP, TCP, ICMP, RTSP, RTP, UDP, IGMP, RTCP, SMTP, SNTP, FTP, DHCP,  UPnP, ARP, DNS, PPPoE, etc.
 Accessories (included)  Power adaptor, camera bracket, RJ45 ethernet cable, quick installation guide,  CD with installation tool/software and User's Manual, ID/Password card.
 Video management software  Surveillance application for viewing and archiving up to 16 cameras
 Users  Up to 20 simultaneous unicast users(depends on video settings)Unlimited  users using multicast
 Alarm and event management  Events triggered by video motion detection
 Notification/upload of JPEG images over FTP and/or email
 Dimensions (HxWxD) and weight  125 x 75 x 35 mm,
 250 g, incl. camera bracket, excl. power adaptor
 Approvals  EMC - CE, FCC Part 15 Subpart B Class B
 Wireless RF - CE, FCC Part 15 Subpart C
 Power supply: FCC, UL EN 60950
 Operating conditions  0-50 ¢XC
 Humidity 20 - 80% RH (non-condensing)
Notice : this spec is for firmware version v010708
 
     
  For more details please email: info@globaltech-online.net
back to top